![]() ![]() The AugmentedīNF (ABNF) for this parameter is shown in Figure 1. ![]() Some values are spare or reserved for national use. That reflects the possible locations where an ISUP call is released. This specification adds a parameter with the ISUP location valueĭefined in to the Reason header field that identifies the Of 100 (Trying), MAY contain a Reason header field with a Q.850 The ISDN location is definedĪs defined by, any SIP Response message, with the exception It can be transported from the originating PSTN entity to the SIPĮntity via a response or BYE message. Of this parameter is to hold the location of the call release so that ISUP interworking gateways and use Q.850 reason codes. The primary intent of the parameter defined in this specification isįor use in IMS (IP Multimedia Subsystem) networks defined by 3GPP,īut it is also open to be used by any other networks that include "OPTIONAL" in this document are to be interpreted as described inīCP 14 when, and only when, they appear in all "SHOULD", "SHOULD NOT", "RECOMMENDED", "NOT RECOMMENDED", "MAY", and The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT", RFC 8606 ISUP Release Location Parameter June 2019 2. Reason of release of a call, and the location identifies where the The cause code is used for identifying the Locations used in ISDN and DSS1 (Digital Subscriber Signalling System describes the definitions of the cause code values and the Only to include the location received by the interworking gateway. Parameter defined in so that the location value canīe interworked from the PSTN. This document adds a location value parameter to the reason-extension The part of the ISUP network where the call was released. specifies that an ISUP Ĭause code can be carried within a SIP response, but not the Q.850 The reason may be a SIP response or an ISUP release cause as Temporary failure) or caused by other factors (e.g., congestion). Termination may be normal, based on a failure within an entity (e.g. The call was interworked to the PSTN, was terminated. Of release indicates why a SIP Dialog or a PSTN call, in cases where that is used to indicate the reason of release. That document specifies the SIP Reason header field Introduction Section 3.4 of describes a SIP message flow for cancelingĪn INVITE request when a REL (release) message is received from the Registration of the Location Parameter for the Reason RFC 8606 ISUP Release Location Parameter June 2019ġ. The Trust Legal Provisions and are provided without warranty as Include Simplified BSD License text as described in Section 4.e of Code Components extracted from this document must Please review these documentsĬarefully, as they describe your rights and restrictions with respect This document is subject to BCP 78 and the IETF Trust's Legal Information about the current status of this document, any errata,Īnd how to provide feedback on it may be obtained atĬopyright (c) 2019 IETF Trust and the persons identified as the Internet Standards is available in Section 2 of RFC 7841. Internet Engineering Steering Group (IESG). Received public review and has been approved for publication by the It represents the consensus of the IETF community. This document is a product of the Internet Engineering Task Force This is an Internet Standards Track document. This document updates RFC 3326 byĪdding a location parameter for this purpose. Released in the PSTN (Public Switched Telephone Network) to correctly Networks may need to know the ISUP location where the call was The SIP Reason header field is defined to carry ISUP (ISDN User Part)Ĭause values as well as SIP response codes. ISDN User Part (ISUP) Cause Location Parameter for the SIP Reason Header Field Request for Comments: 8606 Deutsche Telekom Internet Engineering Task Force (IETF) R. I've configured these options but doesn´t work.RFC 8606: ISDN User Part (ISUP) Cause Location Parameter for the SIP Reason Header Field ICR -> STANDAR -> INCOMING NUMBER: 12345678Ĭould somebody help me with this problem that I've got? The supplier sends the caller ID (12345678). When an incoming calls enters from the trunk line SIP in the traces, the screen shows the error 404 Not Found. With this settings the outgoing calls are out with no problem. SIP LINE -> SIP URI -> REGISTRATION: 1: Credential Authentication Name ![]() SIP LINE -> SIP URI -> LOCAL URI: Use Credential Authentication Name The service's supplier asks as a requirement to the outgoing calls that the "From" field of the SIP URI sends the ID's username. It has to be registered with an username and a password. I have installed in a IP Office 500 Release 9.0 with a SIP trunk like with 50 channels. ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |